Ubiquiti USG-PRO-4 UniFi Security Enterprise Gateway Router with Gigabit Ethernet

Product Information

SFP ports are hot-swappable and support 10/100/1000 fiber SFP modules. If an SFP module is plugged in, then the SFP port is active, and the corresponding WAN port is deactivated. By default, the SFP1 port is set to DHCP Client. Ubiquiti Support cannot assist in the creation of the config.gateway.json file nor will assistance be provided for command line configuration. If assistance is required, feel free to visit our Community to create a topic and ask for help with your desired configuration. we replaced five legacy passive switches in our network with six 8 POE-60W actively managed switches, and Before customizing firewall or NAT rules, take note of the rule numbers used in the UniFi Network Firewall.Default firewall rules start at either 3001 or 6001, and NAT rules will also start at 6001 (which don't overlap with firewall rules). The custom rules created in the config.gateway.jsonfile cannot have duplicate rule numbers with the existing rules in the USG, or there will be a provisioning loop. It is recommended to put custom rules before the existing ruleset, as the lower number will win between two matching rules.

For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply. The main way to differentiate UniFi switches is that the 1st generation model names begin with "US-" and the 2nd generation model names begin with "USW-". See UniFi Switches Comparison and Buyers Guide to compare all available models. New Desktop/Small Switches Note: Although the cabling can be located outdoors, the UniFi Gateway itself should be housed inside a protective enclosure. the best way to fix this issue is by swapping the two OEM fans for Noctua NF-A4x20 PWM Premium-Quality Quiet 40mm fans, as shown in this video, here.The UDM and UXG run a different underlying operating system than the USG. The CPU is an easy way to tell. Older MIPS-based devices EdgeRouters and the USG run EdgeOS. ARM based devices like the UDM and UXG run UniFi OS. An ARM port of EdgeOS is unlikely. UniFi OS is a custom Linux distribution made with Buildroot Linux that mostly follows Debian standards. In their announcement, Ubiquiti said this about UniFi OS: Resets to factory defaults. The UniFi Gateway should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the right LED on the WAN2 port starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the UniFi Gateway will automatically reboot. With DPI on, gigabit performance is possible. With IPS/IDS, throughput drops to 85 Mbps. When being used as a VPN endpoint, throughput is limited to 40 Mbps. See note on hardware offloading below. Used to feed redundant DC power to the UDM-Pro, and 2nd generation Pro/Enterprise switches that support it. Not a switch, but does have an in-band Ethernet management port.

Gigabit routing is no issue, but firewall and encryption speeds are limited, with slightly higher limits than the USG. I was very limited on tools and time, but from what I remember I ended up using a nearby dumb switch, nuking the static IP on the Pi controller, rebooting it, and resetting the USG. (Keeping it completely on it's own network using the dumb switch.) I also made sure the USG was forgotten from the controller.Basically a UDM-Pro without the built-in UniFi OS Console, 8-port Ethernet switch, or 3.5” HD bay for UniFi Protect. Features four 10 Gbps RJ45 Ethernet with PoE++ out. The Enterprise 8 PoE or Flex XG may be better options. RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9 serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed: Find the appropriate section with the custom changes in the config output, for our example above it would be the following: A comprehensive overview of your Network Health is readily available in the new dashboard. Monitor your network’s vitals and make on-the-fly adjustments as needed. Use the configurable reporting and analytics to monitor large user groups and expedite troubleshooting. Advanced search and sorting capabilities make network management more efficient.

Hardware offloading lets you use dedicated hardware to accelerate some tasks. You can turn it on or off depending on what you are trying to do. This applies to the USG/USG-Pro, and also EdgeRouters. Redesigned to be more intuitive and easier to navigate, the new UI raises the bar for enterprise network management efficiency. Important network details are logically organized for a simplified, yet powerful, interface.

RJ45 ports support 10/100/1000 Ethernet connections. A WAN port is active only if the corresponding SFP port is empty. By default, the WAN1 port is set to DHCP Client. Downgrades to dual-core ARM CPU, vs the quad-core on the UDM. Lower IDS/IPS throughput as a result.

Hi,I am trying to deploy an internet calander to all users on Outlook (Not web app). The url is similar to this: https://workintranet/aspx/8789hnjhjehejkhewj. When you manually input this into Outlook internet calendar it will auotmatically sync with our ... Before: our original deployment included a single Unifi Switch 24 aggregator switch, the entry-level USG, the original Cloud Key hardware controller, and three UAP‑HD access points. I would still recommend these devices as a starter kit for those that want to deploy Unifi in a residential setting but substituting the Unifi nanoHD access points if cost is an issue. Original Unifi System. Credit Michael Connelly.

TABLE OF CONTENTS

User Tip: An easy way to test the validity of the json file is: python -m json.tool config.gateway.json Deleting Changes or Reverting to Previous State Enterprise models have higher PoE budgets, faster interfaces such as 2.5 Gbps RJ45 Ethernet, and the features available in the Pro models The UXG-Pro should be able to handle the same levels of connections as the UDM-Pro, which with IDS and IPS disabled can do 3.5Gbps. Both of these products have MIPS processors, with the Vyatta-based EdgeOS underneath. You can create custom json config files for them, which give them some flexibility that the UDM and UXG lines don't have. These can be adopted to an external UniFi Network controller, but offer limited performance and old hardware.