Innokin T22 Pro Kit [Matte Black]

Product Information

Little details such as the On/Off slide switch, easy to see LED indicators and excellent build quality have made this mod feel more expensive than it actually is.

The Innokin ENDURA T22 Pro atomizer has a 4.5ml capacity with a convenient top-filling system. The ENDURA T22 Pro atomizer is compatible with T22 Coil / M18 coils (both not included), providing an unparalleled vaping experience. The T22 Pro atomizer, designed for tight MTL tension, comes with the Endura T22 Pro Kit. This 18mm diameter steel tank has a 2ml reservoir. This may not seem like much, but that's not counting the power-saving resistors. This Innokin atomizer is equipped with a 510 drip tip made of Ultem (Heat Resistant). The kit also includes a second drip tip with a more flared shape. Make sure orings, seal and glass are all in good condition and everything is tight. Make sure the coil is fully inserted and lined up correctly, notice cross-threading. When you use RBA coil, make sure you stuff the cotton in there really good. Please try to vape at an appropriately high wattage which is recommended on the coil during vaping. It may encounter thespittingissue if the liquid on the coil hasn't been atomized on time with low wattage.

The top and bottom faces of the mod match the tank finish – in my case Gunmetal and Silver – and this finish extends around the sides of the mod too. Included in the kit is the new T18E Pro tank which uses the T18 range of coils – I will again go into detail which coils are compatible further in the review. For the 1.7ohm T18e coils, we would recommend high PG e-liquids. We have a huge selection of High PG vape juice in flavours from mixed berry, blue raspberry e-liquid, menthol vape juice and more. The compact size and lightweight design of the T22 Pro make it an ideal choice for users seeking a portable vaping solution without sacrificing performance or functionality. How to Use the T22 Pro Kit

ElementVape.com and any or all of ElementVape.com’s parent and subsidiary companies will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries as well as chargers. Please have a greater understanding of the batteries/chargers you are using and how to care for them properly. One thing I did notice was this tank can be a bit thirstier than my usual pod kit ( Innokin Sceptre) – for one whole battery cycle I had refilled the tank over 10 times.To achieve optimal performance with the T22 Pro kit, it is recommended to use 50/50 nicotine salt e-liquids with a nicotine strength ranging from 10-20mg. The balanced ratio of propylene glycol (PG) to vegetable glycerin (VG) in 50/50 e-liquids ensures smooth vapor production and a satisfying throat hit. However, the T22 Pro kit is also compatible with high PG e-liquids ranging from 3-12mg in nicotine strength, allowing users to explore a wider range of flavors and nicotine options. If you’ve tried the tips above and your battery is not charging properly, you have a faulty battery. Innokin Endura kits cater to new and intermediate vapers through simple design and functionality. A hardwearing build and reliability are a given with the T22 Pro, granting new users peace of mind while on the go. A full charge can easily see you through a full day of vaping thanks to a whopping 3000mAh battery capacity.

In terms of filling, Innokin opted for a Zlide-type top cap that slides open to reveal a filling opening large enough to fill the tank with just about any bottle. You don't need to remove the drip tip to open the tank. Using a 2A charging plug it took to around 2 hours to charge fully. How To Fill the Innokin Endura T22 Pro The 1.7Ω coil looks to be a traditional vertical round wire build, I don’t know if it’s dual or single strand though, not that it matters as long as it delivers.Very gentle not as flavour-full as the 1.7ohm coil at this power level. Feels a lot lower powered and the airflow is tighter still. LED Indicator When charging = the fire button indicator colour displays how much battery charge is remaining – 0-90% = Red LED, higher than 90% = Green LED and when fully charged the LED will go out. Install a new coil making sure the straight edges in the coil base align with the straight edges in the tank as shown. While advanced vapers might turn their nose up at something like the T22 Pro, for a MTL or new vaper, it’s undeniably an attractive option. Verdict