Holts LOYGG8RA Gun Gum Repair Bandage

Product Information

Fumes leaking out of your exhaust in the wrong place can increase your car’s emissions, and they can also damage other parts of your car. A flexible section of an exhaust helps to provide some movement in the system and reduce the risk of fractures. However, if the flexi-section leaks, it’s not so easy to fix. Replacing it is often the only answer. Large exhaust system holes If an exhaust system is blowing around a join, it may be possible to seal it with exhaust paste. This helps to fill any gaps where a clamp is fitted. Dismantle the join, clean it with a wire brush, then apply some exhaust paste. Reassemble the join, fitting a new clamp if necessary. In some cases, running the engine will enable the exhaust paste to dry as the exhaust warms up and thus you have a fix for your blowing exhaust. Flexi-sections A small hole can be the cause of a blowing exhaust and it really doesn’t have to be too big. Finding such a hole can be difficult, but our soapy water method can help. Once a hole has been found, clean the area with a wire brush or wheel to examine it. This will help to see if and how it can be repaired. Exhaust bandages

A blowing exhaust can be caused by a wide range of problems, so we’ll examine each one in detail. And perhaps the best starting point is to identify exactly where it’s coming from, which isn’t always so easy. Where’s the exhaust blowing? The Easy Fit Metal Repair Bandage is an exhaust repair kit from our Gun Gum range containing an adjustable wrap which can be fitted to bends in sections of exhaust or where a silencer box meets a pipe.My wife's Peugeot 106 secondary system pipe had 3 holes. Covered in GunGum, paste and 2 jubilee clips. Lasted for 2 years with no troubles and 2 MOTs until pipe literally fell in 2 due to rust.. If your car’s exhaust sounds like a tractor, follow our guide on how to fix a blowing exhaust to find the problem and fix it. The Holts Gun Gum Flexiwrap Silencer Repair is fully flexible exhaust repair solution. You can adjust it as needed for as tight a seal as possible, allowing you to repair holes and damaged areas easily. No need to dismantle your exhaust, simply fit the flexiwrap for a permanent gas tight seal in minutes. Features & Benefits: Does anybody have any experience with these bandages (gum gum i think they're called) to patch up exhaust holes? Step 4: Wait for the paste to dry overnight. You can also speed up the drying process by running the engine.

When looking for the source of a blowing exhaust, remember that the fumes are dangerous and harmful. So make sure there’s plenty of ventilation. Exhaust manifold blowing The Holts range of Gun Gum exhaust repair products makes it easy for you to fix any section of exhaust on your driveway. A large hole in an exhaust system isn’t so easy to fix with a bandage, exhaust paste or anything else. In most cases, the only answer is to replace that section of the exhaust system. Repair exhaust sections OEM car speakers can be a little underwhelming, especially if you own an older car. We take a look at everything you need to know about the different types of car speakers before you upgrade. If you have heatproof gloves, it may be safe to hold the exhaust where you think it’s blowing. This will help to muffle the bit that’s blowing and find the cause.Providing the exhaust is securely mounted, and free from leaks, it is not a failure if an exhaust bandage or sealant - such as gum gum is used to repair a leak.

The Gun Gum Bandage has been developed to repair small holes for a gas tight seal in minutes. The bandage is easy to use; simply moisten and wrap around the hole, then allow to dry and harden. Problem solved. With this method, you don’t need any special tools and you don’t need to take the exhaust apart. All you need is the ultimate exhaust repair kit: the Gun Gum Exhaust System Repair Paste and the right bandage. What Gun Gum product should you use? If an exhaust is blowing from a join, it may be possible to tighten that connection to seal it. Exhaust clamps can sometimes rattle loose. Or perhaps the wrong size of exhaust clamp is fitted, which means it won’t seal the connection. If the exhaust manifold is still blowing at the cylinder head, fitting a new gasket is our next suggestion. Loose exhaust clampsHoles can develop on different parts of your exhaust, so the Gun Gum range contains products that can fix any area. The company has developed a variety of bandages for different parts of the exhaust system, for example ends or bends. When you use these with the Gun Gum exhaust paste it creates a permanent, gas tight seal that will fix the problems ahead of your MOT – and cost a lot less than a replacement exhaust. They should be considered a temporary repair, but can last for many months if applied correctly. I have found that a good seal can be achieved if you wrap some tin plate around the damaged section before applying the bandage. Where a join in an exhaust is leaking, it may help to tighten any clamps or other fastenings. If that doesn’t help, what next? Where a flange is fitted, there may be a seal or gasket that can be replaced. This will involve separating the join where the exhaust is blowing. However, it may not mean the exhaust system needs to be removed. Providing there’s room to separate the exhaust and replace the gasket or seal, you can do it in situ. Exhaust paste Gun Gum Wide Metal Repair Bandage is fully flexible, so you can adjust it to the size of your exhaust silencer. There’s no need to dismantle your exhaust, making it ideal for home repairs. Simply apply Holts Gun Gum paste and fit the flexiwrap over the damaged area for a permanent gas tight seal in minutes.

yeah, itll pass. dont mention it to them though, emmisions is your only worry as exhaust is loaded with its own pressure in the test.... On balance, if its a small hole on a straight pipe and you know your getting it fixed / getting rid of the car in a week or two, you should be alright, otherwise your'e better off replacing the exhaust. Step 2: Wearing protective gloves, apply a thin layer of Gun Gum Exhaust System Repair Paste to the damaged area with the included spatula. A blowing exhaust can be a bit of an embarrassment. It may sound loud, but to most people it’s hardly the music out of the exhaust on a performance car. Plus, you could get stopped by the police, no matter where you are in the world. I had a rust hole in the pipe in front of the silencer and patched it with repair tape. The repair was perfect and very long lasting, but unfortunately the pipe continued to rust underneath the bandage. The repair was gas-tight right up to the day the exhaust pipe snapped in half.Our specially developed Metal Repair Bandage is an easy to use solution for wide, straight pipes. Always use together with Holts Gun Gum paste for a permanent, gas tight seal. Common problems with some exhaust systems have resulted in repair sections becoming available. This often arises on an expensive component, such as a catalytic converter or DPF. If it’s common for a connecting end to corrode and break, then a repair section may be available. This will usually involve removing the component to fit the repair. Welding repairs Spraying soapy liquid over a join or where the exhaust manifold mates to the cylinder head can also help. If air is blowing out of where you spray, it will be easier to spot the soapy liquid. This may turn into frothy bubbles, which are even easier to see. The Holts Gun Gum Putty provides a gas tight seal on your exhaust, permanently repairing small holes and leaks in silencers and exhaust systems. Gun Gum is a leading car exhaust repair putty which has been trusted by car lovers for decades. It creates a gas tight seal, and permanent repair is guaranteed, giving you peace of mind that your exhaust is working as it should. You simply press and smooth the paste over the hole or damaged area and leave it to dry, making it an easy DIY solution for home exhaust repairs. The Holts Gun Gum Exhaust Repair Bandage is an exhaust repair products which been developed so that you can repair larger holes and splits in your exhaust system at home. The bandage is easy to use, simply wrap around and seal for a permanent gas tight seal. You can also use it with Gun Gum Paste for end plate leaks and small holes. The bandage is easy to use; simply moisten and wrap around the hole, then allow to dry and harden. Features & Benefits: