Unlocked ZTE MF286D CAT 12 600mbps 4G+/LTE Home/Office Router (White). 2 x RJ11 Tel Ports. 2 x External Antennas. Works with any Mobile Network Sim Worldwide. 2.4/5GHz Wi-Fi + Bridge Mode (Renewed)

Product Information

Mobiilireitittimen asetukset ovat oletuksena oikein, eikä niitä tarvitse erikseen muokata. Halutessasi voit muokata ja hallita laitteen hallintaliittymän kautta. This router connects to the internet using the Three 4G network, just like your mobile phone. It uses a SIM card to get online, rather than using a traditional fibre broadband connection.

The function set is similar to other stationary LTE routers. The main screen of the configuration interface shows a network diagram where you can go to LTE settings, Wi-Fi or a list of connected devices. An interesting thing is the ability to choose the bandwidth that can be used by the modem built into the router. However, the Wi-Fi capability is much larger, above all the advantage is simultaneous operation in the 2.4 GHz and 5 GHz band. The router has a Wi-Fi optimization function – it scans the radio band, detects existing networks and automatically selects the best channel. You can enable an additional guest network (Multi SSID) on both frequencies, limit the number of clients in each SSID network, and set a time limit for guests (in hours).Well so far my pi based Speedtest box has consistently shown higher results using the ZTE device than the B535 so it must be doing so eh thing better. ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1 After installing QMI, you can either put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP, or add the interface through LuCI. UBIFS (ubi0:2): FS size: 18411520 bytes (17 MiB, 145 LEBs), journal size 1015809 bytes (0 MiB, 7 LEBs)

Previously using just the one bluespot antenna externally speeds would range from about 10-15mbit in extremely busy periods and up to about 65mbit in the early hours of the morning. Of course, there are no miracles in practice, the LTE speeds drop down in real use. Wi-Fi bandwidth is also a fraction of the theoretical value: between computers in the LAN and WLAN during testing it did not exceed 288 Mbit/s. Like other desktop routers, the ZTE MF286 has four Gigabit Ethernet ports, a USB 2.0 port for connecting a USB drive and file sharing, as well as an analog telephone line connector. Of course, there is also a built-in modem and a slot for mini SIM cards, under the plugs, two SMA connectors for the external LTE antenna. qmi_wwan 2-1:1.5 usb0: register 'qmi_wwan' at usb-xhci-hcd.0.auto-1, Qualcomm WWAN/QMI device, 26:33:ea:44:56:9dunknown 2020, unknown 2019, unknown 2018, Available 2020, Available 2019, Available 2018, Available 2017, Discontinued 2020, Discontinued 2019, Discontinued 2018, Discontinued 2017, Discontinued 2016, Discontinued 2015, Discontinued 2014, Discontinued 2013, Discontinued 2012, Discontinued 2011, Discontinued 2010, Discontinued

Just a couple of general OpenWrt queries. Can you disable the very unsecure WPS button? Can you totally disable WiFi? Bridge Mode does not work? You can only double NAT via DHCP for WAN port use? Linux version 5.10.100 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18801-56256259a1) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Feb 12 22:50:26 2022

No. Unfortunately, the 4G Hub (ZTE MF286D) does not support 5G connectivity. You’ll need to get Three’s 5G home broadband on the 5G Hub if you want access to faster 5G speeds. Internetyhteys toimii taas normaalisti. Hallintasivulla laite ohjautuu suoraan Päivitys-kohtaan. Kuvallisen ohjeen päivitykseen löydät täältä. Hello, so i am at the same point, the CP2102 i bought doesn't give me any output on Putty, and after followed some advices in OpenWRT forum, i got Nordic V11, and now the framework says is not a proper version.

So for the Usb to TTL i have this could be the same issue for me too? Just grab the one you mentioned and install it through the listed commands in OpenWRT official installation guide? Looking online briefly, the ZTE router is Wi-Fi 5 only. Assuming 2x2 for 866MHz, I guess that's still fine but if you have a better router then you might benefit from the improvements of Wi-Fi 6 and other features. My Huawei LTE routers are pretty basic, so I assume ZTE, TCL and others are similar. In some cases, you might not be able to get 4G home broadband, even if you’re within Three’s 4G network coverage area as shown on the coverage map. If this is the case, you’ll be shown the following error message:In this article, we’ve tested and reviewed the Three 4G Hub, also known as the ZTE MF286D, to see if it’s any good. Heikkoon 3G/4G-kuuluvuuteen voit kokeilla esimerkiksi lisäantennia. MF286-reitittimessä on kaksi antennipaikkaa (SMA). ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1 msm_pcie_probe: msm_pcie_probe: PCIe: RC0 is not enabled during bootup; it will be enumerated upon WAKE signal.