Rothenberger 80000 Monoblock Tap Spanner Set

Product Information

Completely removing the nut from the stud will allow the tap to be removed complete with its flexible hoses. Make sure no associated washers or seals are left hanging up. Take care when you withdraw the hose ends, especially on stainless steel sinks where sharp edges can figure. To remove the tap(s) loosen the nut that clamps it to the mounting surface, gripping the tap to stop it rotating. You might need assistance if you can’t reach it. Tools you’ll find useful for this task are a flathead screwdriver, a tap spanner, an adjustable spanner and a pair of grips. A monobloc tap is a modern-looking design that utilises one lever to control both the hot and the cold water flow. Pull-out Spray Mixer. With an extendable hose, this tap is perfect for rinsing dishes and food and can be used to control the flow of the water.

A granite sink offers an alternative to ceramic and stainless steel and is more hardwearing. A granite sink will not scratch, chip or stain, and can withstand high temperatures and harsh chemicals. Again, the granite sink is available in a variety of styles and colours to suit any kitchen or bathroom design however the price may be slightly more expensive. Brushed, Matt or Satin. These different finishes are available on a range of tap designs and offer an alternative to chrome. When selecting the style of your sink you have several options to consider. Sinks are available as single bowls or double bowls, or even a double bowl with a central half sink. If you are installing a new kitchen sink, remember that it will be heavily used so consider a design that works for your home. When it comes to inbuilt drainage space you might want to consider opting for a stainless steel sink, but if you are more focused on design, a ceramic or graphite sink could work better with your décor and integrate seamlessly with the worktops. Once you have chosen the material and style of your sink the next step is to choose the taps that will go with it. Just like sinks, taps are available in different styles, materials and sizes. If you are thinking of installing a mixer tap with your sink you will need to consider whether your water pressure is adequate as they need a higher pressure to operate properly. Choosing the right tap size is also important with smaller taps working well for small sinks and larger taps for bigger sinks. The types of taps that are widely available are:Plumbing in a new mixer tap is a fairly simple job and should take between 30 minutes to an hour to install depending on the level of experience of the person installing it. If at any point of the installation you are unsure or require help it is recommended to have a professional plumber on hand that you can call for advice. Once you have settled on the material, design and finish of your taps, you will want to turn your attention to where the tap is mounted. The two choices of mounting are sink mounted or worktop mounted, but you will also need to make sure that the spout of the tap is long enough to reach the centre of your sink. Maintaining Your Taps Take the flexible tap tails that came with your new tap and screw them into the main tap body. Gently tighten then up. Fit horseshoe rubber and plate over the threaded rods under the sink and screw on the nuts and tighten with a box spanner. Hoses are pre-fitted to mixer taps. If not, screw the hoses into the tap base carefully, tightening by hand only. Follow the instructions which come with the tap. Feed the mains connection ends through the location hole - be careful with the sharp edges on stainless steel sinks and make sure any seals, gaskets, washers and studs are pre-fitted and located according the instruction’s steps.

Pop-up waste. A pop-up waste tap helps you to empty the sink with a mechanism that means you do not need to pull the chain and plug – simply use the tap instead! When fitting a new kitchen or bathroom, you’ll want to choose taps and sinks that go well together. Before shopping, remember to measure the space that you have available and take this with you. In some bathrooms and kitchens there just is not enough space to install a basin that is very deep or very wide, so you will have to keep this in mind. There are many different sink designs and materials to choose from, and it can be hard to make the right decision, so we’ve created the following guide to help you choose. Firstly, when choosing a sink there are different materials you can choose from. Though fitting a full bathroom suite is a job you’ll want to get a professional in to do, if you’ve got a bit of DIY and plumbing experience, then fitting a mixer tap to the basin in your bathroom is a job you can do relatively easily. Start by removing your old mixer tap using the steps outline above and wiping down the area to make sure it is clean from any debris. You can get mixer taps for kitchens, baths and basins. Basin mixer taps are generally smaller because they don’t need to deliver as much water as a tap in a bath or kitchen. PreparationFit the threaded bars first before dropping the tap through the hole in the basin. Tighten them by hand to avoid causing damage to the thread. Now that the tap is fixed in place you can connect the pipework. Use speedfit fittings or standard fittings of the right size to connect the water supply to the feed pipes. Ensure that fittings are tightened up securely. Rather than the old days of two separate taps for hot and cold water flow, a mixer tap ‘mixes’ the hot and cold water within the main body of a single tap. On top there is usually a lever/handle that you can pull up to establish water flow and to either side to determine water temperature. Before actually removing or replacing any part of your water system it’s advisable to first turn the water off and drain down the system if you can.