Drayton Wiser Smart Heating Room Thermostat

Product Information

The actuator head of a ACL Lifestyle 2-port motorised valve (679H308-30L1) has failed. Is it still possible to get the actuator for this valve to avoid draining the whole system? I’m not sure about rating this as “amazing” (5 stars) but “better than expected” (4) didn’t seem a fit either..it’s a central heating thermostat..can’t we just give a star rating without these associated comments??

day / 2-day programming:This groups weekdays and the weekend separately, so you can set a schedule for your weekdays and a separate schedule for the weekend. The TRV is liquid filled this gives a fast response to temperature and provides a greater temperature accuracy. No, E1 is an error code that means the internal sensor has failed. The sender unit will have to be replaced. Depending on the fuel type you select during installation will affect how Digistat works with your boiler/heat source - so ensure to select the correct type during installation. Digistat supports the following fuel types:We did notice a slight delay of around 10 seconds to one minute between boosting the heating from both the radiator thermostat or the app and the boiler springing into action. The further away from the Heat Hub the thermostat is, the longer the delay. Initially, we also struggled to get the radiator thermostat in the room furthest from the Heat Hub to remain connected to the system at all times. It would often drop the signal, meaning we were unable to control it via the app. However, after installing an optional Wiser Smart Plug – which also doubles as a range extender for the system – in a room between the Heat Hub and the troublesome radiator thermostat, connection issues were no longer a problem. My Digistat +2/3 appears to switch off before my set point is reached and sometimes remains on after my set point is reached, is this normal? Powered by two AA batteries, the smart thermostat can be freestanding on a table or shelf, or mounted on a wall. It has three touch controls on the front. The plus and minus button allow you to adjust the desired temperature of the room, while the middle button boosts the heating in said room by two degrees. The screen automatically goes to sleep after 15 seconds to conserve the battery, but pressing any of the three touch controls will wake it up.

Typically 30M, however building construction and materials may effect this. Signal strength test should be carried out.Drayton Wiser may be functional, but its plain all-white plastic design certainly isn’t stylish. If you prefer gadgets that make a design statement, this isn’t the smart thermostat for you. From the home screen, you can also view the weather for your location and sunrise and sunset times, too. The cog icon at the top of the home screen provides access to the main Settings menu, from where you can activate smart modes such as Eco and Comfort, and set a temperature for the Away mode. I have a Drayton TRV4 thermostatic valve on the radiator. Is it correct that it can be installed on both the Flow or Return and can be mounted either horizontal or vertical?

The Digistat is universal because it can be used as a fully-programmable thermostat or as a simple manual thermostat. In fact it contains 4 types of functionality: The Digistat remembers the last BOOST so if you always use the same parameters just press the O button 3 times. Simple!What I always mention reviewing this item is to get any kind of accuracy with this set up (which is vital in my circumstances of course) you need one of these stats for every room, I bought the system believing the radiator valves were sufficient and only one stat was needed for “the most important/main room” my finding was despite the valves apparently being adjusted to allow for being close to the radiators when sensing the room’s temperature it just didn’t work, you got a sort of boom/bust situation. The heating would run, the area by the rad was of course much warmer than the room the valve shut the radiator believing the space was at temperature and it could be 8 degrees off..eventually the radiator would cool, the valve would realise the room was freezing..it would run the boiler/open and so on, essentially the room was never sufficiently warm. I think this is a common criticism of thermostatic valves, I’ve never bothered with them until now/my engineer doesn’t like them. Trv’s might be different in a modern/efficient house -can’t say, maybe try it out? I used my old stats display/with it disconnected as a room thermometer(it’s battery powered) to tell me what was happening in statless areas. I have a Digistat+RF room unit with my combi boiler. Is it possible that interference from other wireless appliances can occur, ie computer systems, walkie talkies, radio controlled toys? Manual thermosta:This option has no schedule and controls by temperature only. You set your preferred temperature and adjust it with the + and - buttons. You can tap on a room and edit the schedule or access the room settings, where you can view the battery level for the thermostat, rename it and turn Open Window Detection on or off. Editing a schedule was made super-easy as a result of the ‘copy’ feature, which lets you duplicate a schedule with just one tap, rather than having to input it all for each day and on each device. The information provided in this document contains general descriptions, technical characteristics and/or recommendations related to products/solutions.